ABRITES DIAGNOSTICS FOR PEUGEOT/CITROËN

The ABRITES diagnostics for Peugeot/Citroën is a very competent diagnostic software which is used together with the ABRITES Vehicle Diagnostic Interface (AVDI) in order to perform vehicle diagnostics as well as advanced diagnostics on Peugeot and Citroën vehicles. The ABRITES Diagnostics for Peugeot/Citroën (PSA) is designed to provide an OEM and higher level of diagnostics at a fraction of the cost.

The ABRITES Diagnostics for Peugeot/Citroën (PSA) is one of the most progressive and forward placed aftermarket diagnostic solutions to diagnosing Peugeot/Citroën (PSA) vehicles in the world. Standard diagnostic functions can be performed online over three separate protocols - K-line, CAN and UDS, completely by OBDII. Standard diagnostic capabilities include:

• Reading and clearing of Diagnostic Trouble Codes (DTCs), acquire full details of when and under what circumstances they occurred and remove them after the problem which caused them has been resolved
• Live values monitoring from all electronic modules and sensors using graph and table view
• Actuator testing - activating and deactivating various actuators on demand in order to properly determine the cause of each fault
• Module identification
• BSI - Service interval reset, clear faults log, verify/set PIN, virginize
• Change ID in BSI, Telematics, Airbag, MDS
• Clear crash data in some Airbag modules by DUMP (offline)

The ABRITES Diagnostics for Peugeot/Citroën (PSA) covers All CAN and UDS Peugeot/Citroën (PSA) vehicles as well as many K-line vehicles, however the focus of the software remains on the latest vehicles produced by the French manufacturer.

You will need a basic AVDI software package and Annual Maintenance subscription in order to use the ABRITES Diagnostics for Peugeot/Citroën (PSA).

With the PIN Manager users of the ABRITES software licenses are able to read PIN code and program keys to PSA vehicles.
Also changing the PIN code of the BSI module and exchanging the module is made possible.

• PIN code reading from BSI or Engine Control Unit
• Key programming

Mileage recalibration is made possible by disabling dashboard synchronization or independent recalibration to the dashboard (via offline by OBD for Peugeot 208/2008/301/308 II/508 up to 2015, Citroen C3 II/C4 II/C4 II Picasso/C5 II/DS4/DS5/C-Elysee/Cactus upto 2015, by DUMP for Peugeot 206/308). With this special function you can replace the dashboard in these models.

Combined with PN018 unlocks BSI Exchange function to replace BSI module.

The Peugeot/Citroën Built-in System Interface is a control module, essential to the vehicles. It controls a large amount of the vehicle's operation. Given its many tasks this module is very susceptible to failure. The cost of a new module and the main dealer prices for an exchange of a failed BSI is normally high, the BSI exchange special function provides a cost effective way out for the customer, allowing a repair shop to adapt a second-hand BSI in just a few clicks. The BSI exchange feature allows you to read and store the data of one BSI and transfer it to another. It is extremely important to use the same hardware when exchanging.

For Valeo UDS 2012+ and Continental UDS 2010+ you can directly read/update ConfData.

The ABRITES Diagnostics for Peugeot/ Citroen offers advanced diagnostic functions. One of them is EEPROM and FLASH reading from the ECUs of the supported models. Reading and modifying mileage in the dashboard, as well as calibration of various modules is made possible with ABRITES automotive software solutions.

• Reading, saving and updating the engine control unit's (ECU) ConfData and flash
• PIN code reading
• Cluster calibration
• IMMO OFF and after sales preparation of the unit –in order to be used in another vehicle
• Updating ECU service lists

There is also a visualisation available of the error history from the Engine control units, useful when performing maintenance, general servicing or rebuilds.

The ABRITES software for Peugeot and Citroën also gives the opportunity to match virgin Engine Control Units to BSI modules, which is invaluable when it comes to module adaptation.

And last, but not least, clearing of the error history for some models Service Zero Reset (a.k.a. Oil reset) for all CAN protocol supporting models. Supported models are all models using the following electronic control units: EDC15, EDC16, EDC17, SID201, SID801, SID801A, SID802, SID803, SID803A, SID804, SID806.