MORE FUNCTIONALITIES NOW AVAILABLE IN THE BASIC AVDI PACKAGE!
We are happy to announce that we are adding even more FREE functionalities for all AVDI users with active AMS!
From now on, you can access a selection of ANxxx licenses (legacy functionalities) with the basic software. These solutions allow key programming and mileage calibration, as well as facilitate module replacement in VAG Immo III and III+ vehicles. This goes for the following special functions and licenses:
AN002 and AN003 - reading CAN TP2.0 dashboards 2003-2008.
They are used for PIN/CS reading, mileage calibration on these dashboards in all VW/Seat/Skoda 2003-2008 (Immo III/III+ cars). This functionality is mainly used for preparing keys and mileage calibration.
AN004 - Allows to manually change the Immo data for the modules above. This can be used to adapt a dashboard (immobilizer) for all VW/Seat/Skoda 2003-2008 (Immo III/III+ vehicles).
AN005 - Used for new ECU adaptation in Immo III (excluding Immo III+) through adaptation by diagnostics on channel 50.
AN006 - Allows reading EEPROMs on dashboards that use K-Line protocol. These are all 1998-2003 dashboards (VDO, Magneti Marelli, Motometer, on VW/Seat/Skoda), as well as Bosch RB4/RB8 dashboards (RB4 - 2001-2004 VW Golf/Audi A4, RB8 - Audi A4 2004-2008) . You can extract PIN/CS to program keys and calibrate mileage.
AN007 - Used for reading the EDC15 (2000-2004) and ME7 (2000-2006) ECUs.
Also, extracting CS/PIN which can be used for key learning and module replacement (through adaptation by diagnostics on channel 50).
AN010 - Allows reading the EEPROM of Airbags that use the K-Line protocol (1997-2004).
AN012 - Allows odometer replacement on EDC16 (2004-2008).
AN014 - Used for EDC17 PIN reading (excluding CS) - used for programming dealer keys (excluding preparing) for EDC17/MED17 2007-2010.
AN018/AN019 - Allows reading EEPROM of EZS-Kessy on Audi 4F (A6 2003-2008, Q7 2005-2008). Used for extracting PIN/CS and key programming for these vehicles.
AN021 - Used for reading the ME7 EEPROM via CAN protocol. These ECUs are used in vehicles such as the Audi TT 2003-2010. This functionality allows extracting the PIN/CS, which are used for key programming.
AN023 - Used for Crafter Key programming in vehicles 2006-2012 equipped with EDC16.
AN024 - Allows key programming for all Immo III/III+ vehicles, if PIN/CS is known (can be read with one of the other licenses) and a dealer key is present.
АN025 - Allows reading the PIN/CS from EDC16/MED9/Simos PPD/Simos 7.x ECUs.
AN026 - Used for dealer key preparation and programming (for all Immo III/III+ vehicles). It is used to find the 7th byte of the Immobilizer (if the Component Security bytes from the ECU can be read).
AN027 - same as AN018/19, but extended to A6 2003-2010, Q7 2005-2014.
AN028/AN029 - Allows UDS Dashboard Reading - VDO 2008-2015, JCI 2008-2012, Magneti Marelli 2006-2014. These are all used in VW/Seat/Skoda 2008-2013, as well as Audi A1/Q3. It is used to calibrate mileage and program keys (spare key and All Keys Lost).
What’s more, now the special functions for JLR - JL003 and JL004 will be available to every AVDI user with active AMS. This means that mileage calibration and key programming for Jaguar and Land Rover vehicles up to 2018 is now part of the basic AVDI software.
• Spare key programming
• ALL KEYS LOST key programming
• Remote control and keyless programming are part of the procedure, so no extra steps are required.
Supported models for key learning are equipped with the following KVM types:
• DPLA
• FK72
• HPLA
Supported models for mileage recalibration (including but not limited to):
Land Rover
• Evoque (L538) - LL and HL (2- and 4-door models)
• Range Rover Sport (L494)
• Range Rover (L405) (including long wheel base)
Jaguar
• F-Type Convertible and Coupe
• XF (X250)
• XJ (X351)
• XK (X150)
• XKR (X150)
The FN012 special function now also becomes a part of the basic AVDI package. This means that the following is available For FCA vehicles up to 2012 without the need for additional purchases:
• Key programming by OBDII
• Transponders/Keys preparation by dump of Immobiliser
• BCM – Configuration data read and update, PIN, component protection data
• BCM Read/Update ConfData by OBDII
Supported models for key programming:
• Fiat, Alfa, Lancia – Alfa 147, Mito; Fiat 500, Bravo, Grande punto, Croma, Doblo, Ducato, Fiorino, Idea, Palio, Panda, Stilo; Lancia Thesis, Delta.
Supported units:
• BCM Delphi (93C66) – NOTE: PIN Code is required!
• BCM Marelli (912DG128, 3K91D)
• BCM Marelli (9S12DG256, 1K79X)
• BCM Marelli (NEC 70F3237/70F3378,95160)
• BCM Marelli (NEC 70F3633,95320)
• BCM Siemens (9S12DG128)
Get your AVDI now, or renew your AMS if you are already an Abrites user, in order to access all these newly added functionalities! Be advised that the ZN002 PROTAG Programmer may be required for certain key programming functionalities.
