The Abrites diagnostics for Peugeot/ Citroën is a very competent diagnostic software which is used together with the Abrites Vehicle Diagnostic Interface (AVDI) In order to perform vehicle diagnostics as well as advanced diagnostics on Peugeot and Citroën vehicles. Some of the main characteristics of the Abrites Diagnostic Software for PSA include the following within the basic diagnostic package.
The Abrites Diagnostics for Peugeot/ Citroën (PSA) is one of the most progressive and forward placed aftermarket diagnostic solutions to diagnosing Peugeot/ Citroën (PSA) vehicles in the world. With its help you will be able to perform reading and clearing of Diagnostic Trouble Codes (DTC), acquire full details of when and under what circumstances they occurred and remove them after the problem which caused them has been resolved. Using the Abrites Diagnostics for Peugeot/ Citroën (PSA) you can view live values from all electronic modules and sensors using a graph and table types of monitoring and activate and deactivate various actuators on demand in order to properly determine the cause of each fault. The Abrites Diagnostics for Peugeot/ Citroën (PSA) covers All CAN and UDS Peugeot/ Citroën (PSA) vehicles as well as many K-line vehicles, however the focus of the software always was and will be the latest vehicles produced by the French manufacturer. The Abrites Diagnostics for Peugeot/ Citroën (PSA) is designed to provide an OEM and higher level of diagnostics at a fraction of the cost. You will need a basic AVDI set and Annual Maintenance subscription in order to use the Abrites Diagnostics for Peugeot/ Citroën (PSA). With the help of the software you can also reset the service intervals of these vehicles in order to be able to perform maintenance of Peugeot/ Citroën (PSA) vehicles.
In terms of the so-called "Advanced diagnostics" the Abrites diagnostic software for PSA provides an almost unlimited functionality where almost every modern vehicle produced by Peugeot/Citroën are supported.
The reading and writing of EEPROM is supported for the engine control units in order to have a backup to repair the car in case of any issues.
Features and highlights:
ALL OF THE BELOW ARE PERFORMED COMPLETELY BY THE ON BOARD DIAGNOSTICS CONNECTOR (OBDII):
Apart from basic diagnostic functions the Abrites Diagnostcs from PSA contains extremely strong functionality in terms of special functions. Its main advantages, compared to the other products on the market are the support for 2015+ vehicles equipped with Continental BSIs both for PIN Extraction, odometer calibration and EEPROM reading and writing and the BSI Exchange special function permitting users to adapt a second-hand BSI to the vehicle. Complete description of the separate special functions can be seen below:
Supported models are all models using the following electronic cotrol units: EDC15, EDC16, EDC17, SID201, SID801, SID801A, SID802, SID803, SID803A, SID804, SID806.
This function can be used independently.
Supported models for PIN code reading :
C3 (1.4 HDI)*
C5 (2.0 HDI)*
C5 II 2007+
Xsara (2.0 HDI)*
Xsara Picasso (2.0 HDI)*
Saxo (1.4 HDI)*
Berlingo (2.0 HDI)*
Xantia (2.0 HDI)*
Picasso (2.0 HDI)*
Lancia Phedra 2008+
The key learning function can be used only if the PIN code is already known. If the read security code operation was previously completed correctly, the key learning procedure can take the already retrieved PIN code, otherwise you will have to enter the PIN code manually.
Supported vehicles for mileage recalibration:
Citroën Berlingo 2008+
C5 II 2007+
Lancia Phedra 2008+
BSI Exchange - allows you to read the whole content of the one BSI (JCI or Valeo CAN) and transfer it to another one. It is very important to use the same hardware type for the replacement BSI. The Valeo BSIs are two types - the old one is thick, while the new one is thin, so they can’t be mistaken. To use this special function you need to have PN012 + PN013 special fucntions. The UDS BSI modules are supported via read/write EEPROM and flash.