Menu Vehicle diagnostics software and hardware

Vehicle diagnostics, key programming and key learning software

Shop

ABRITES Diagnostics for Peugeot/Citroën and Peugeot/Citroën (Online)

 
 

DIAGNOSTICS FOR PEUGEOT/CITROËN

The Abrites diagnostics for Peugeot/ Citroën is a very competent diagnostic software which is used together with the Abrites Vehicle Diagnostic Interface (AVDI) In order to perform vehicle diagnostics as well as advanced diagnostics on Peugeot and Citroën vehicles. Some of the main characteristics of the Abrites Diagnostic Software for PSA include the following within the basic diagnostic package.

Standard diagnostic features

The Abrites Diagnostics for Peugeot/ Citroën (PSA) is one of the most progressive and forward placed aftermarket diagnostic solutions to diagnosing  Peugeot/ Citroën (PSA) vehicles in the world. With its help you will be able to perform reading and clearing of Diagnostic Trouble Codes (DTC), acquire full details of when and under what circumstances they occurred and remove them after the problem which caused them has been resolved. Using the Abrites Diagnostics for Peugeot/ Citroën (PSA) you can view live values from all electronic modules and sensors using a graph and table types of monitoring and activate and deactivate various actuators on demand in order to properly determine the cause of each fault. The Abrites Diagnostics for Peugeot/ Citroën (PSA) covers All CAN and UDS Peugeot/ Citroën (PSA) vehicles as well as many K-line vehicles, however the focus of the software always was and will be the latest vehicles produced by the French manufacturer. The Abrites Diagnostics for Peugeot/ Citroën (PSA) is designed to provide an OEM and higher level of diagnostics at a fraction of the cost. You will need a basic AVDI set and Annual Maintenance subscription in order to use the Abrites Diagnostics for Peugeot/ Citroën (PSA). With the help of the software you can also reset the service intervals of these vehicles in order to be able to perform maintenance of Peugeot/ Citroën (PSA) vehicles.

 

In terms of the so-called "Advanced diagnostics" the Abrites diagnostic software for PSA provides an almost unlimited functionality where almost every modern vehicle produced by Peugeot/Citroën are supported.

The reading and writing of EEPROM is supported for the engine control units in order to have a backup to repair the car in case of any issues.

Features and highlights:

ALL OF THE BELOW ARE PERFORMED COMPLETELY BY THE ON BOARD DIAGNOSTICS CONNECTOR (OBDII):

  • PIN Code Reading and key programming - the software is designed in such a way so that it can be as user-friendly as possible for easy and quick work for all our locksmith customers
  • Mileage reading and calibration for a vast variety of models for all relevant modules, which also includes disabling of cluster synchronization as well as the ability to work with all the latest models by directly updating the EEPROM
  • Reading and modifying mileage in the dashboard of newer models that without the need of disabling the synchronization
  • BSI Exchange - for all CAN and UDS protocol vehicles. The Peugeot/Citroën Built-in System Interface is a control module, essential to the vehicles. It controls a large amount of the vehicle's operation. Given its many tasks this module is very susceptible to failure. Given the cost of a new module and the main dealer prices for an exchange of a failed BSI, the "BSI exchange" special function provides a cost effective way out for the customer, allowing a repair shop to adapt a second hand BSI in just a few mouse clicks
  • Instrument cluster Read/Update Conf data
  • BSI Read/Update Conf data
  • Instrument cluster exchange - A broken instrument cluster is an extremely hard task to undertake by any repair shop. We know that and have tried to turn it into an easy task for people who are willing to perform it (please contact the support team for supported models)
  • Reading EEPROM and FLASH from the ECUs
  • Changing the PIN code of the BSI
  • Visualization and fault log clearing for BSI modules
  • Matching virgin Engine Control Units to BSI modules
  • Visualization of the error history from the Engine control units
  • Clearing of the error history for some models
  • Service Zero Reset (a.k.a Oil reset) for all CAN protocol supporting models - an essential part of any service workshop performing maintenance, general servicing or rebuilds
  • Airbag crash data management - allows the user to clear the crash data after repairing the vehicle thus restoring the normal operation of the car after an accident - an excellent solution for any accident damage repair shop

Special Functions

Apart from basic diagnostic functions the Abrites Diagnostcs from PSA contains extremely strong functionality in terms of special functions. Its main advantages, compared to the other products on the market are the support for 2015+ vehicles equipped with Continental BSIs both for PIN Extraction, odometer calibration and EEPROM reading and writing and the BSI Exchange special function permitting users to adapt a second-hand BSI to the vehicle. Complete description of the separate special functions can be seen below:

Engine control unit advanced diagnostic

  • Allows you to read and write the EEPROM of the EDC15, EDC17(BOOT MODE), SID201, SID801, SID801A, SID802, SID803, SID803A, SID804, SID806;
  • Allows you to read and write the FLASH of the EDC15, EDC17(BOOT MODE), SID201, SID801, SID801A, SID802, SID803, SID803A, SID804, SID806;
  • Reading and modifying mileage in the dashboard of EDC15
  • Allows you to read and change the PIN of EDC15, SID201, SID801, SID801A, SID802, SID803, SID803A, SID804, SID806;
  • Allows you to modify the service intervals of EDC15, SID201, SID801, SID801A, SID802, SID803, SID803A, SID804, SID806;
  • Allows you to read and write the EEPROM of EDC15 Engine ECUs and make Immo OFF,as well as after sales and edit service list.

Supported models are all models using the following electronic cotrol units: EDC15, EDC16, EDC17, SID201, SID801, SID801A, SID802, SID803, SID803A, SID804, SID806.

This function can be used independently.

PIN Manager and key programming


With this special function you can read PIN codes from the BSI module. Supported models are all CAN and UDS protocol models which includes almost all models produced after 2004
This function can be used independently.

Supported models for PIN code reading :

Peugeot Citroën

1007

206 (1,4 HDI, 2.0 HDI)*

207

306 (2.0 HDI)*

307 (2.0 HDI)*

307 2005+

208 2012+

2008 2013+

301 2012+

308

308 II

3008

508

5008

406 (2.0 HDI)*

407

607 2006+

807 2006+

Expert II

Partner (2.0 HDI)*

Ranch (2.0 HDI)*

Partner 2008+

Citroen C3 2013

Citroen Jumpy 2016+

Toyota ProAce 2016+

Lancia Phedra 2008+

 

C2

C3 (1.4 HDI)*

C3 2006+

C3 II

DS3

C4

C4 Picasso

C4 II

DS4

C5 (2.0 HDI)*

C5 2004+

C5 II 2007+

DS5

C6

C8 2007+

Jumpy II

Xsara (2.0 HDI)*

Xsara Picasso (2.0 HDI)*

Saxo (1.4 HDI)*

Berlingo (2.0 HDI)*

Berlingo 2008+

Xantia (2.0 HDI)*

Picasso (2.0 HDI)*

C-Elysee 2012+

Peugeot Expert 2016

Citroen C3 Picasso 2013

Citroen C3 Aircross 2013+

 

The key learning function can be used only if the PIN code is already known. If the read security code operation was previously completed correctly, the key learning procedure can take the already retrieved PIN code, otherwise you will have to enter the PIN code manually.

- Improved support for Continental UDS BSI 2015+

BSI, Instrument cluster data manager


With this special function you can read and and calibrate the mileage stored in the BSI module and remove the synchronization with the instrument cluster
(i.e. The modification is performed in the BSI exclusively and after a complete ignition cycle the mileage is not restored to the original value). In the cases where the sync removal does not apply it can calibrate the mileage in the cluster exclusively. Supported models are all CAN and UDS protocol models which includes almost all models produced after 2004.
This function can be used independently.

Supported vehicles for mileage recalibration:

Peugeot Citroën

1007


207


307 2005+


208 2012+


2008 2013+


301 2012+


Citroën Berlingo 2008+


308


3008


508


5008


407


607 2006+


807 2006+


Expert II

Partner 2008+

Citroen C3 2013

Citroen Jumpy 2016+

Toyota ProAce 2016+

Peugeot 3008 II

Peugeot 308 II2016+

Peugeot Expert2017+

 

C-Elysee 2012+


C2


C3 2006+


C3 II


DS3


C4


C4 Picasso


C4 II


DS4


C5 2004+


C5 II 2007+


DS5


C6


C8 2007+


Jumpy II


Lancia Phedra 2008+

Peugeot Expert 2016

Citroen C3 Picasso 2013

Citroen C3 Aircross 2013+

Citroen C32016+

Citroen C4Picasso II2016+

Citroen Jumpy2017+

Toyota ProAce 2017+

Citroen C3 2013

Citroen Jumpy 2016+

Toyota ProAce 2016+

22-readkm208 23-changekm208

 

BSI Exchange - allows you to read the whole content of the one BSI (JCI or Valeo CAN) and transfer it to another one. It is very important to use the same hardware type for the replacement BSI. The Valeo BSIs are two types - the old one is thick, while the new one is thin, so they can’t be mistaken. To use this special function you need to have PN012 + PN013 special fucntions. The UDS BSI modules are supported via read/write EEPROM and flash.

Screenshots:

1 Main screen 7 Special functions main